iMS Motion Solution (Johor) Sdn Bhd
7, Jalan Sasa 4,
Taman Gaya,
81800 Ulu Tiram,
Johor, Malaysia.
+607-8635240
+607-8637240
1700-818-330 (Hotline)
+60167336610

Policies

 

UTM Slip-ring-less rotating torque meter

Previous 1 / 2 Next

UTM Slip-ring-less rotating torque meter Torque Meter Load Cell & Torque Sensor
RM 0.00
In Stock


New series with 5kHz high-speed response & noise resistance digital output!
 
∵17 different capacities ranging from 0.05Nm to 10000Nm.
∵Analog bandwidth 5kHz with high-speed sampling rate of 20kHz.
∵Safe overload of 500%
∵Power supply DC24V
∵Rated torque at ±10V
∵Digital zero function via external signal
∵Digital output via RS-485
∵Equipped with pulse output for rotation detection

Increased resistance to radial & thrust load
Influences that radial and thrust loads exert on effective accuracy were dramatically reduced.

⊆Why is load other than torque applied at torque meter?
For torque measurement, when interlocking shafts, misalignments on shaft center as illustrated below occurs by all means.
The devices that absorb radial and thrust loads caused by such misalignments are couplings. However, even the couplings cannot completely absorb such radial and thrust loads, resulting in an impact on torque measurement.

Major misalignments when mounting shafts

Experimental data

 
Above illustration shows the output change when one shaft end of UTMIII-2Nm is fixed, and 7N radial load is applied at another shaft end through the bearing.
Output changes depending on rotation angle.
While output value changes 0.1% at maximum with conventional torque meter, output value changes less than 0.01% with UTMIII.

Abundant options available

More compact for side-by-side measurement

Added zero correction function with external signal

Frequency bandwidth of 5kHz, variable filter

Digital output via RS-485

Connection example


Sample application


Specifications

±0.05Nm to ±2Nm

Measurement
range
±0.05
Nm
±0.1Nm ±0.2Nm ±0.5Nm ±1Nm ±2Nm
Power supply DC24V ±15%
Consumption current 100mA or less
Output range ±10V DC Load resistance must be more than 5kΩ
Responsivity 5kHz
Rotation
signal
4 pulses per 1 rotation *1
Open collector Max. ratings 30V, 10mA
Digital filter 1Hz to 1kHz(Depending on settings) PASS 5kHz
Safe overload 500%FS
Non-linearity 0.03%FS or less
Hysteresis 0.03%FS or less
Repeatability 0.03%FS or less
Operation
temp. range
-10 to +50→
Temp. effect on ZERO 0.01%FS/→ or below
Temp. effect on span 0.01%FS/→ or below
Max. rotation speed 25000rpm
Torsional
spring
constant
5.67
Nm/rad
11.57
Nm/rad
26.10
Nm/rad
93.1
Nm/rad
188
Nm/rad
414
Nm/rad
Maximum
torsional
angle
8.81×
10-3rad
(0.505°)
8.64×
10-3rad
(0.495°)
7.66×
10-3rad
(0.439°)
5.37×
10-3rad
(0.308°)
5.32×
10-3rad
(0.305°)
4.83×
10-3rad
(0.277°)
Inertia
moment
8.48×
10-7
kgm2
8.58×
10-7
kgm2
8.7×
10-7
kgm2
1.46×
10-6
kgm2
1.49×
10-6
kgm2
1.39×
10-6
kgm2
Ext.
dimension
(case size/
W×H×D)
54×49×32mm
Total length 74mm 84mm
Shaft
diameter
φ5mm φ8mm
Weight Approx. 140g Approx. 160g
Supplied
cable
12-conductor flexible cable (2m) Cable end: 5 wires
→ Cable length is switchable to 5m(Option:UTM-L5)
Optionally
available
cable
CATM351:12-conductor flexible cable (5m) Cable end: 5 wires
CATM312:12-conductor flexible cable (10m) Cable end: 5 wires
CE marking
certificatio
EMC directives EN61326-1,EN61326-2-3

Permissible shaft end load *2

Measurement
range
±0.05Nm ±0.1Nm ±0.2Nm ±0.5Nm ±1Nm ±2Nm
RadialN 0.12N 0.25N 0.3N 0.5N 1N 8N
ThrustN 3N 4N 5N 6N 8N 30N
RadialN
(R, RC, RK, RCK)
0.07N 0.14N 0.17N 0.3N 0.6N 5N
ThrustN
(R, RC, RK, RCK)
3N 4N 5N 6N 8N 30N

Option

Measurement
range
±0.05Nm ±0.1Nm ±0.2Nm ±0.5Nm ±1Nm ±2Nm
Key Groove            
Rotary encoder
Key groove &
Rotary encoder
           
Centering
location
Key groove &
Centering location
           
Rotary encoder &
Centering location
Key groove &
Rotary encoder &
Centering location
           
*1 0.05 to 10Nm model can be changed to 60 pulses in 1 rotation specification. Contact us for more details.
*2 Radial N and Thrust N of permissible shaft end load are the values guaranteeing that influence for torque output is less than 0.03% when those loads apply.

±5Nm∥±200Nm

Measurement
range
±5Nm ±10Nm ±20Nm ±50Nm ±100Nm ±200Nm
Power supply DC24V ±15%
Consumption current 100mA or less 150mA or less
Output range ±10V DC Load resistance must be more than 5kΩ
Responsivity 5kHz
Rotation
signal
4 pulses per 1 rotation *1
Open collector Max. ratings 30V, 10mA
Digital filter 1Hz to 1kHz(Depending on settings) PASS 5kHz
Safe overload 500%FS
Non-linearity 0.03%FS or less
Hysteresis 0.03%FS or less
Repeatability 0.03%FS or less
Operation
temp. range
-10 to +50→
Temp. effect on ZERO 0.01%FS/→ or below
Temp. effect on span 0.01%FS/→ or below
Max. rotation speed 25000rpm 20000rpm 15000
rpm
12000
rpm
Torsional
spring
constant
691
Nm/rad
1851
Nm/rad
5386
Nm/rad
8428
Nm/rad
17.3×
103
Nm/rad
41.7×
103
Nm/rad
Maximum
torsional
angle
7.24×
10-3rad
(0.415°)
5.40×
10-3rad
(0.310°)
3.71×
10-3rad
(0.213°)
5.93×
10-3rad
(0.340°)
5.78×
10-3rad
(0.331°)
4.79×
10-3rad
(0.275°)
Inertia
moment
3.56×
10-6
kgm2
3.66×
10-6
kgm2
2.59×
10-5
kgm2
2.66×
10-5
kgm2
6.59×
10-5
kgm2
1.40×
10-4
kgm2
Ext.
dimension
(case size/
W×H×D)
57×54×37mm 70×63×47mm 67×
63.5×
56mm
67×68×
61mm
Total length 97mm 150
mm
170
mm
177mm 187mm
Shaft
diameter
φ12mm φ20mm φ25mm φ30mm
Weight Approx. 250g Approx. 670g Approx.
1.1kg
Approx.
1.4kg
Supplied
cable
12-conductor flexible cable (2m) Cable end: 5 wires
→ Cable length is switchable to 5m(Option:UTM-L5)
Optionally
available
cable
CATM351:12-conductor flexible cable (5m) Cable end: 5 wires
CATM312:12-conductor flexible cable (10m) Cable end: 5 wires
CE marking
certificatio
EMC directives EN61326-1,EN61326-2-3

Permissible shaft end load *2

Measurement
range
±5Nm ±10Nm ±20Nm ±50Nm ±100Nm ±200Nm
RadialN 15N 20N 23N 60N 90N 160N
ThrustN 40N 100N 360N 400N 500N 800N
RadialN
(R, RC, RK, RCK)
7N 13N 20N 25N 60N 100N
ThrustN
(R, RC, RK, RCK)
40N 100N 360N 400N 500N 800N

Option

Measurement
range
±5Nm ±10Nm ±20Nm ±50Nm ±100Nm ±200Nm
Key Groove
Rotary encoder
Key groove &
Rotary encoder
Centering
location
Key groove &
Centering location
   
Rotary encoder &
Centering location
Key groove &
Rotary encoder &
Centering location
   
*1 0.05 to 10Nm model can be changed to 60 pulses in 1 rotation specification. Contact us for more details.
*2 Radial N and Thrust N of permissible shaft end load are the values guaranteeing that influence for torque output is less than 0.03% when those loads apply.

±500Nm∥±10000Nm

Measurement
range
±500Nm ±1000Nm ±2000Nm ±5000Nm ±10000Nm
Power supply DC24V ±15%
Consumption current 150mA
or less
180mA or less
Output range ±10V DC Load resistance must be more than 5kΩ
Responsivity 5kHz
Rotation
signal
4 pulses per 1 rotation *1
Open collector Max. ratings 30V, 10mA
Digital filter 1Hz to 1kHz(Depending on settings) PASS 5kHz
Safe overload 500%FS
Non-linearity 0.03%FS or less
Hysteresis 0.03%FS or less
Repeatability 0.03%FS or less
Operation
temp. range
-10 to +50→
Temp. effect on ZERO 0.01%FS/→ or below
Temp. effect on span 0.01%FS/→ or below
Max. rotation speed 10000
rpm
7000rpm 6000rpm 5000rpm 4000rpm
Torsional
spring
constant
117×103
Nm/rad
377×103
Nm/rad
717×103
Nm/rad
1649×103
Nm/rad
3255×103
Nm/rad
Maximum
torsional
angle
4.28×
10-3rad
(0.246°)
2.65×
10-3rad
(0.152°)
2.79×
10-3rad
(0.160°)
3.03×
10-3rad
(0.174°)
3.07×
10-3rad
(0.176°)
Inertia
moment
4.70×
10-4
kgm2
2.90×
10-3
kgm2
5.89×
10-3
kgm2
2.01×
10-2
kgm2
5.16×
10-2
kgm2
Ext.
dimension
(case size/
W×H×D)
67×78×
71mm
86×103×
98mm
86×119×
111mm
97×141×
137mm
103×166×
162mm
Total length 217mm 286mm 306mm 387mm 447mm
Shaft
diameter
φ40mm φ60mm φ70mm φ90mm φ110mm
Weight Approx.
2.6kg
Approx.
7.4kg
Approx.
10.6kg
Approx.
21.7kg
Approx.
36.2kg
Supplied
cable
12-conductor flexible cable (2m) Cable end: 5 wires
→ Cable length is switchable to 5m(Option:UTM-L5)
Optionally
available
cable
CATM351:12-conductor flexible cable (5m) Cable end: 5 wires
CATM312:12-conductor flexible cable (10m) Cable end: 5 wires
CE marking
certificatio
EMC directives EN61326-1,EN61326-2-3

Permissible shaft end load *2

Measurement
range
±500Nm ±1000Nm ±2000Nm ±5000Nm ±10000Nm
RadialN 300N 400N 500N 1000N 1200N
ThrustN 1800N 3000N 4500N 7000N 11000N
RadialN
(R, RC, RK, RCK)
200N
ThrustN
(R, RC, RK, RCK)
1800N

Option

Measurement
range
±500Nm ±1000
Nm
±2000
Nm
±5000
Nm
±10000
Nm
Key Groove
Rotary encoder        
Key groove &
Rotary encoder
       
Centering
location
       
Key groove &
Centering location
       
Rotary encoder &
Centering location
       
Key groove &
Rotary encoder &
Centering location
       
*1 0.05 to 10Nm model can be changed to 60 pulses in 1 rotation specification. Contact us for more details.
*2 Radial N and Thrust N of permissible shaft end load are the values guaranteeing that influence for torque output is less than 0.03% when those loads apply.

iMS Motion Solution (Johor) Sdn Bhd (Company Registration 1098771-W)
 
No.7, Jalan Sasa 4,Taman Gaya, 81800 Ulu Tiram, Johor Bahru, Johor. Malaysia.
TEL:+607-8635240 FAX: +607-8637240
MOBILE: +6019-6774477
EMAIL: info@ims.com.my | WhatsApp  | www.ims.com.my
HOTLINE : 1700-818-330
whatsapp us now !

Brand Name
MEISTER | GGM | Sanyo Denki | ElectroCraft | EDrive | SHIHLIN ELECTRIC | AUTONICS | UI Robot | Mitsubishi CNC | PANASONICApex Dynamics | NISSEI GTR | UNIPULSE | CREVIS
 
MOTION DEVICES SPECIALIST | SYSTEM and CONTROL INTEGRATION |
| Induction Motor | Speed Control Motor | Reversible Motor |Brake Motor |BLDC Motor |DC Motor |Planetary Gear Motor | Servo Motor | Stepping Motor | Linear Actuator Motor | Lead Screw Motor|Close Loop Stepping Motor | Customization Motors | Right Angle Gear Head | Precision Gear Reducer |PLC | Motion Controller |HMI /Touch Screen| Inverter |CNC Controller |Multi Axis Robots |IPC | SCADA |Monitoring Software | Embeded PC | Remote IO |TPC | Motion Card | Loadcell |PPC |
 
Return / Refund Policy : 
All goods sold are not returnable & we accept goods ex-change with equal or lower value of good purchased. If the ex-change items are higher than purchased items, buyer shall top up the differential cost. All payment made are not refundable, please confirm the purchase items code & cost with our sales representative before place orders.
 
Shipping and Fulfillment :
Thank you for your purchase. Once we have confirmed your payment, we will prepare and ship out your order out within 24-48 hours.( For ex-stock items only, Indent items subject to delivery stated in quotation & conversation in emails). Once your order has been shipped out, you will receive an email notification with the tracking number and tracking details inside.
 
Private Policy
General Statement of Principles 
As described in detail below, any information we gather at this web site is strictly for our use and is not shared with any other entity, public or private, for any reason - period. We will not sell or give away any lists or other data that we may retain and we do not purchase such information from other sources.
Statistical Data 
Our servers (as most) track IP addresses and referring pages to help with site maintenance and improvements. This data is viewed only as anonymous statistics to show the busiest times of the day or week, pages with errors and how effective our advertising has been. This information is not used for any other purpose.
Personal Information Collected - Order Forms
With the exception of credit card info, we store the information from your order form to allow us to track consulting issues or refer to a previous order to help provide some customer service. You may elect to have your information completely removed from this system by e-mailing us at info@ims.com.my with your request. We do not store any type of sales information.
Information Correction or Removal 
If you wish to correct, update or remove any information about you that may be in our records, please send us e-mail at info@ims.com.my with the details of your request. If you wish to contact us further, please find complete contact information on our contact page.
Cookies
Cookies are files with small amount of data, which may include an anonymous unique identifier. Cookies are sent to your browser from a web site and stored on your computer's hard drive. We use 'cookies' to store your cart contents for you. You can instruct your browser to refuse all cookies or to indicate when a cookie is being sent. However, if you do not accept cookies, you may not be able to use the checkout section of our site.
 
Changes To This Privacy Policy
This Privacy Policy is effective as of 1st Jan 2019 and will remain in effect except with respect to any changes in its provisions in the future, which will be in effect immediately after being posted on this page.


 

Please leave your enquiry here, we will reply as soon as possible.
Name*  
Company Name  
Product Interested  
Quantity  
Email*  
Contact No.*  
Ship to Name  
Shipping Address  
Attachment  
*only support gif, jpeg, jpg, png, pdf
Messages*  

Our Agency Product Brands
   

You have 0 items in you cart. Would you like to checkout now?
0 items
Switch to Mobile Version
available in
Recent Updates
Subscribe Newsletter
1
Hello! Thanks for visiting my site. Please press Start button to Contact with Admin :)

Start