Share:
New series with 5kHz high-speed response & noise resistance digital output!
●17 different capacities ranging from 0.05Nm to 10000Nm.
●Analog bandwidth 5kHz with high-speed sampling rate of 20kHz.
●Safe overload of 500%
●Power supply DC24V
●Rated torque at ±10V
●Digital zero function via external signal
●Digital output via RS-485
●Equipped with pulse output for rotation detection
Increased resistance to radial & thrust load
Influences that radial and thrust loads exert on effective accuracy were dramatically reduced.
■Why is load other than torque applied at torque meter?
For torque measurement, when interlocking shafts, misalignments on shaft center as illustrated below occurs by all means.
The devices that absorb radial and thrust loads caused by such misalignments are couplings. However, even the couplings cannot completely absorb such radial and thrust loads, resulting in an impact on torque measurement.
Major misalignments when mounting shafts
Major misalignments when mounting shafts
Experimental data
Above illustration shows the output change when one shaft end of UTMIII-2Nm is fixed, and 7N radial load is applied at another shaft end through the bearing.
Output changes depending on rotation angle.
While output value changes 0.1% at maximum with conventional torque meter, output value changes less than 0.01% with UTMIII.
Abundant options available
Abundant options available
More compact for side-by-side measurement
Added zero correction function with external signal
Frequency bandwidth of 5kHz, variable filter
Digital output via RS-485
Connection example
Sample application
Specifications
» Measurement range:±0.05Nm to ±2Nm
» Measurement range:±5Nm to ±200Nm
» Measurement range:±500Nm to ±10000Nm
» Measurement range:±5Nm to ±200Nm
» Measurement range:±500Nm to ±10000Nm
±0.05Nm to ±2Nm
|
Measurement range |
±0.05 Nm |
±0.1Nm | ±0.2Nm | ±0.5Nm | ±1Nm | ±2Nm |
|---|---|---|---|---|---|---|
| Power supply | DC24V ±15％ | |||||
| Consumption current | 100mA or less | |||||
| Output range | ±10V DC Load resistance must be more than 5kΩ | |||||
| Responsivity | 5kHz | |||||
|
Rotation signal |
4 pulses per 1 rotation *1 Open collector Max. ratings 30V, 10mA |
|||||
| Digital filter | 1Hz to 1kHz(Depending on settings) PASS 5kHz | |||||
| Safe overload | 500％FS | |||||
| Non-linearity | 0.03％FS or less | |||||
| Hysteresis | 0.03％FS or less | |||||
| Repeatability | 0.03％FS or less | |||||
|
Operation temp. range |
-10 to +50℃ | |||||
| Temp. effect on ZERO | 0.01%FS/℃ or below | |||||
| Temp. effect on span | 0.01%FS/℃ or below | |||||
| Max. rotation speed | 25000rpm | |||||
|
Torsional spring constant |
5.67 Nm/rad |
11.57 Nm/rad |
26.10 Nm/rad |
93.1 Nm/rad |
188 Nm/rad |
414 Nm/rad |
|
Maximum torsional angle |
8.81× 10-3rad (0.505°) |
8.64× 10-3rad (0.495°) |
7.66× 10-3rad (0.439°) |
5.37× 10-3rad (0.308°) |
5.32× 10-3rad (0.305°) |
4.83× 10-3rad (0.277°) |
|
Inertia moment |
8.48× 10-7 kgm2 |
8.58× 10-7 kgm2 |
8.7× 10-7 kgm2 |
1.46× 10-6 kgm2 |
1.49× 10-6 kgm2 |
1.39× 10-6 kgm2 |
|
Ext. dimension (case size/ W×H×D) |
54×49×32mm | |||||
| Total length | 74mm | 84mm | ||||
|
Shaft diameter |
φ5mm | φ8mm | ||||
| Weight | Approx. 140g | Approx. 160g | ||||
|
Supplied cable |
12-conductor flexible cable (2m) Cable end: 5 wires → Cable length is switchable to 5m（Option：UTMⅢ-L5） |
|||||
|
Optionally available cable |
CATM351：12-conductor flexible cable (5m) Cable end: 5 wires CATM312：12-conductor flexible cable (10m) Cable end: 5 wires |
|||||
|
CE marking certificatio |
EMC directives EN61326-1,EN61326-2-3 | |||||
Permissible shaft end load *2
|
Measurement range |
±0.05Nm | ±0.1Nm | ±0.2Nm | ±0.5Nm | ±1Nm | ±2Nm |
|---|---|---|---|---|---|---|
| RadialN | 0.12N | 0.25N | 0.3N | 0.5N | 1N | 8N |
| ThrustN | 3N | 4N | 5N | 6N | 8N | 30N |
|
RadialN (R, RC, RK, RCK) |
0.07N | 0.14N | 0.17N | 0.3N | 0.6N | 5N |
|
ThrustN (R, RC, RK, RCK) |
3N | 4N | 5N | 6N | 8N | 30N |
Option
|
Measurement range |
±0.05Nm | ±0.1Nm | ±0.2Nm | ±0.5Nm | ±1Nm | ±2Nm |
|---|---|---|---|---|---|---|
| Key Groove | ||||||
| Rotary encoder | ○ | ○ | ○ | ○ | ○ | ○ |
|
Key groove & Rotary encoder |
||||||
|
Centering location |
○ | ○ | ○ | ○ | ○ | ○ |
|
Key groove & Centering location |
||||||
|
Rotary encoder & Centering location |
○ | ○ | ○ | ○ | ○ | ○ |
|
Key groove & Rotary encoder & Centering location |
*1 0.05 to 10Nm model can be changed to 60 pulses in 1 rotation specification. Contact us for more details.
*2 Radial N and Thrust N of permissible shaft end load are the values guaranteeing that influence for torque output is less than 0.03% when those loads apply.
*2 Radial N and Thrust N of permissible shaft end load are the values guaranteeing that influence for torque output is less than 0.03% when those loads apply.
±5Nm～±200Nm
|
Measurement range |
±5Nm | ±10Nm | ±20Nm | ±50Nm | ±100Nm | ±200Nm |
|---|---|---|---|---|---|---|
| Power supply | DC24V ±15％ | |||||
| Consumption current | 100mA or less | 150mA or less | ||||
| Output range | ±10V DC Load resistance must be more than 5kΩ | |||||
| Responsivity | 5kHz | |||||
|
Rotation signal |
4 pulses per 1 rotation *1 Open collector Max. ratings 30V, 10mA |
|||||
| Digital filter | 1Hz to 1kHz(Depending on settings) PASS 5kHz | |||||
| Safe overload | 500％FS | |||||
| Non-linearity | 0.03％FS or less | |||||
| Hysteresis | 0.03％FS or less | |||||
| Repeatability | 0.03％FS or less | |||||
|
Operation temp. range |
-10 to +50℃ | |||||
| Temp. effect on ZERO | 0.01%FS/℃ or below | |||||
| Temp. effect on span | 0.01%FS/℃ or below | |||||
| Max. rotation speed | 25000rpm | 20000rpm |
15000 rpm |
12000 rpm |
||
|
Torsional spring constant |
691 Nm/rad |
1851 Nm/rad |
5386 Nm/rad |
8428 Nm/rad |
17.3× 103 Nm/rad |
41.7× 103 Nm/rad |
|
Maximum torsional angle |
7.24× 10-3rad (0.415°) |
5.40× 10-3rad (0.310°) |
3.71× 10-3rad (0.213°) |
5.93× 10-3rad (0.340°) |
5.78× 10-3rad (0.331°) |
4.79× 10-3rad (0.275°) |
|
Inertia moment |
3.56× 10-6 kgm2 |
3.66× 10-6 kgm2 |
2.59× 10-5 kgm2 |
2.66× 10-5 kgm2 |
6.59× 10-5 kgm2 |
1.40× 10-4 kgm2 |
|
Ext. dimension (case size/ W×H×D) |
57×54×37mm | 70×63×47mm |
67× 63.5× 56mm |
67×68× 61mm |
||
| Total length | 97mm |
150 mm |
170 mm |
177mm | 187mm | |
|
Shaft diameter |
φ12mm | φ20mm | φ25mm | φ30mm | ||
| Weight | Approx. 250g | Approx. 670g |
Approx. 1.1kg |
Approx. 1.4kg |
||
|
Supplied cable |
12-conductor flexible cable (2m) Cable end: 5 wires → Cable length is switchable to 5m（Option：UTMⅢ-L5） |
|||||
|
Optionally available cable |
CATM351：12-conductor flexible cable (5m) Cable end: 5 wires CATM312：12-conductor flexible cable (10m) Cable end: 5 wires |
|||||
|
CE marking certificatio |
EMC directives EN61326-1,EN61326-2-3 | |||||
Permissible shaft end load *2
|
Measurement range |
±5Nm | ±10Nm | ±20Nm | ±50Nm | ±100Nm | ±200Nm |
|---|---|---|---|---|---|---|
| RadialN | 15N | 20N | 23N | 60N | 90N | 160N |
| ThrustN | 40N | 100N | 360N | 400N | 500N | 800N |
|
RadialN (R, RC, RK, RCK) |
7N | 13N | 20N | 25N | 60N | 100N |
|
ThrustN (R, RC, RK, RCK) |
40N | 100N | 360N | 400N | 500N | 800N |
Option
|
Measurement range |
±5Nm | ±10Nm | ±20Nm | ±50Nm | ±100Nm | ±200Nm |
|---|---|---|---|---|---|---|
| Key Groove | ○ | ○ | ○ | ○ | ○ | ○ |
| Rotary encoder | ○ | ○ | ○ | ○ | ○ | ○ |
|
Key groove & Rotary encoder |
○ | ○ | ○ | ○ | ○ | ○ |
|
Centering location |
○ | ○ | ○ | ○ | ○ | ○ |
|
Key groove & Centering location |
○ | ○ | ○ | ○ | ||
|
Rotary encoder & Centering location |
○ | ○ | ○ | ○ | ○ | ○ |
|
Key groove & Rotary encoder & Centering location |
○ | ○ | ○ | ○ |
*1 0.05 to 10Nm model can be changed to 60 pulses in 1 rotation specification. Contact us for more details.
*2 Radial N and Thrust N of permissible shaft end load are the values guaranteeing that influence for torque output is less than 0.03% when those loads apply.
*2 Radial N and Thrust N of permissible shaft end load are the values guaranteeing that influence for torque output is less than 0.03% when those loads apply.
±500Nm～±10000Nm
|
Measurement range |
±500Nm | ±1000Nm | ±2000Nm | ±5000Nm | ±10000Nm |
|---|---|---|---|---|---|
| Power supply | DC24V ±15％ | ||||
| Consumption current |
150mA or less |
180mA or less | |||
| Output range | ±10V DC Load resistance must be more than 5kΩ | ||||
| Responsivity | 5kHz | ||||
|
Rotation signal |
4 pulses per 1 rotation *1 Open collector Max. ratings 30V, 10mA |
||||
| Digital filter | 1Hz to 1kHz(Depending on settings) PASS 5kHz | ||||
| Safe overload | 500％FS | ||||
| Non-linearity | 0.03％FS or less | ||||
| Hysteresis | 0.03％FS or less | ||||
| Repeatability | 0.03％FS or less | ||||
|
Operation temp. range |
-10 to +50℃ | ||||
| Temp. effect on ZERO | 0.01%FS/℃ or below | ||||
| Temp. effect on span | 0.01%FS/℃ or below | ||||
| Max. rotation speed |
10000 rpm |
7000rpm | 6000rpm | 5000rpm | 4000rpm |
|
Torsional spring constant |
117×103 Nm/rad |
377×103 Nm/rad |
717×103 Nm/rad |
1649×103 Nm/rad |
3255×103 Nm/rad |
|
Maximum torsional angle |
4.28× 10-3rad (0.246°) |
2.65× 10-3rad (0.152°) |
2.79× 10-3rad (0.160°) |
3.03× 10-3rad (0.174°) |
3.07× 10-3rad (0.176°) |
|
Inertia moment |
4.70× 10-4 kgm2 |
2.90× 10-3 kgm2 |
5.89× 10-3 kgm2 |
2.01× 10-2 kgm2 |
5.16× 10-2 kgm2 |
|
Ext. dimension (case size/ W×H×D) |
67×78× 71mm |
86×103× 98mm |
86×119× 111mm |
97×141× 137mm |
103×166× 162mm |
| Total length | 217mm | 286mm | 306mm | 387mm | 447mm |
|
Shaft diameter |
φ40mm | φ60mm | φ70mm | φ90mm | φ110mm |
| Weight |
Approx. 2.6kg |
Approx. 7.4kg |
Approx. 10.6kg |
Approx. 21.7kg |
Approx. 36.2kg |
|
Supplied cable |
12-conductor flexible cable (2m) Cable end: 5 wires → Cable length is switchable to 5m（Option：UTMⅢ-L5） |
||||
|
Optionally available cable |
CATM351：12-conductor flexible cable (5m) Cable end: 5 wires CATM312：12-conductor flexible cable (10m) Cable end: 5 wires |
||||
|
CE marking certificatio |
EMC directives EN61326-1,EN61326-2-3 | ||||
Permissible shaft end load *2
|
Measurement range |
±500Nm | ±1000Nm | ±2000Nm | ±5000Nm | ±10000Nm |
|---|---|---|---|---|---|
| RadialN | 300N | 400N | 500N | 1000N | 1200N |
| ThrustN | 1800N | 3000N | 4500N | 7000N | 11000N |
|
RadialN (R, RC, RK, RCK) |
200N | – | – | – | – |
|
ThrustN (R, RC, RK, RCK) |
1800N | – | – | – | – |
Option
|
Measurement range |
±500Nm |
±1000 Nm |
±2000 Nm |
±5000 Nm |
±10000 Nm |
|---|---|---|---|---|---|
| Key Groove | ○ | ○ | ○ | ○ | ○ |
| Rotary encoder | ○ | ||||
|
Key groove & Rotary encoder |
○ | ||||
|
Centering location |
○ | ||||
|
Key groove & Centering location |
○ | ||||
|
Rotary encoder & Centering location |
○ | ||||
|
Key groove & Rotary encoder & Centering location |
○ |
*1 0.05 to 10Nm model can be changed to 60 pulses in 1 rotation specification. Contact us for more details.
*2 Radial N and Thrust N of permissible shaft end load are the values guaranteeing that influence for torque output is less than 0.03% when those loads apply.
iMS Motion Solution (Johor) Sdn Bhd (Company Registration 1098771-W)
All goods sold are not returnable & we accept goods ex-change with equal or lower value of good purchased. If the ex-change items are higher than purchased items, buyer shall top up the differential cost. All payment made are not refundable, please confirm the purchase items code & cost with our sales representative before place orders.
Shipping and Fulfillment :
Thank you for your purchase. Once we have confirmed your payment, we will prepare and ship out your order out within 24-48 hours.( For ex-stock items only, Indent items subject to delivery stated in quotation & conversation in emails). Once your order has been shipped out, you will receive an email notification with the tracking number and tracking details inside.
Private Policy
General Statement of Principles
As described in detail below, any information we gather at this web site is strictly for our use and is not shared with any other entity, public or private, for any reason - period. We will not sell or give away any lists or other data that we may retain and we do not purchase such information from other sources.
Statistical Data
Our servers (as most) track IP addresses and referring pages to help with site maintenance and improvements. This data is viewed only as anonymous statistics to show the busiest times of the day or week, pages with errors and how effective our advertising has been. This information is not used for any other purpose.
Personal Information Collected - Order Forms
With the exception of credit card info, we store the information from your order form to allow us to track consulting issues or refer to a previous order to help provide some customer service. You may elect to have your information completely removed from this system by e-mailing us at info@ims.com.my with your request. We do not store any type of sales information.
Information Correction or Removal
If you wish to correct, update or remove any information about you that may be in our records, please send us e-mail at info@ims.com.my with the details of your request. If you wish to contact us further, please find complete contact information on our contact page.
Cookies
Cookies are files with small amount of data, which may include an anonymous unique identifier. Cookies are sent to your browser from a web site and stored on your computer's hard drive. We use 'cookies' to store your cart contents for you. You can instruct your browser to refuse all cookies or to indicate when a cookie is being sent. However, if you do not accept cookies, you may not be able to use the checkout section of our site.
Changes To This Privacy Policy
This Privacy Policy is effective as of 1st Jan 2019 and will remain in effect except with respect to any changes in its provisions in the future, which will be in effect immediately after being posted on this page.
*2 Radial N and Thrust N of permissible shaft end load are the values guaranteeing that influence for torque output is less than 0.03% when those loads apply.
iMS Motion Solution (Johor) Sdn Bhd (Company Registration 1098771-W)
No.7, Jalan Sasa 4,Taman Gaya, 81800 Ulu Tiram, Johor Bahru, Johor. Malaysia.
TEL:+607-8635240 FAX: +607-8637240
MOBILE: +6019-6774477
EMAIL: info@ims.com.my | WhatsApp | www.ims.com.my
HOTLINE : 1700-818-330
whatsapp us now !
Return / Refund Policy : whatsapp us now !
Brand Name
| MEISTER | GGM | Sanyo Denki | ElectroCraft | EDrive | SHIHLIN ELECTRIC | AUTONICS | UI Robot | Mitsubishi CNC | PANASONIC| Apex Dynamics | NISSEI GTR | UNIPULSE | CREVIS
| MOTION DEVICES SPECIALIST | SYSTEM and CONTROL INTEGRATION |
| Induction Motor | Speed Control Motor | Reversible Motor |Brake Motor |BLDC Motor |DC Motor |Planetary Gear Motor | Servo Motor | Stepping Motor | Linear Actuator Motor | Lead Screw Motor|Close Loop Stepping Motor | Customization Motors | Right Angle Gear Head | Precision Gear Reducer |PLC | Motion Controller |HMI /Touch Screen| Inverter |CNC Controller |Multi Axis Robots |IPC | SCADA |Monitoring Software | Embeded PC | Remote IO |TPC | Motion Card | Loadcell |PPC |
All goods sold are not returnable & we accept goods ex-change with equal or lower value of good purchased. If the ex-change items are higher than purchased items, buyer shall top up the differential cost. All payment made are not refundable, please confirm the purchase items code & cost with our sales representative before place orders.
Shipping and Fulfillment :
Thank you for your purchase. Once we have confirmed your payment, we will prepare and ship out your order out within 24-48 hours.( For ex-stock items only, Indent items subject to delivery stated in quotation & conversation in emails). Once your order has been shipped out, you will receive an email notification with the tracking number and tracking details inside.
Private Policy
General Statement of Principles
As described in detail below, any information we gather at this web site is strictly for our use and is not shared with any other entity, public or private, for any reason - period. We will not sell or give away any lists or other data that we may retain and we do not purchase such information from other sources.
Statistical Data
Our servers (as most) track IP addresses and referring pages to help with site maintenance and improvements. This data is viewed only as anonymous statistics to show the busiest times of the day or week, pages with errors and how effective our advertising has been. This information is not used for any other purpose.
Personal Information Collected - Order Forms
With the exception of credit card info, we store the information from your order form to allow us to track consulting issues or refer to a previous order to help provide some customer service. You may elect to have your information completely removed from this system by e-mailing us at info@ims.com.my with your request. We do not store any type of sales information.
Information Correction or Removal
If you wish to correct, update or remove any information about you that may be in our records, please send us e-mail at info@ims.com.my with the details of your request. If you wish to contact us further, please find complete contact information on our contact page.
Cookies
Cookies are files with small amount of data, which may include an anonymous unique identifier. Cookies are sent to your browser from a web site and stored on your computer's hard drive. We use 'cookies' to store your cart contents for you. You can instruct your browser to refuse all cookies or to indicate when a cookie is being sent. However, if you do not accept cookies, you may not be able to use the checkout section of our site.
Changes To This Privacy Policy
This Privacy Policy is effective as of 1st Jan 2019 and will remain in effect except with respect to any changes in its provisions in the future, which will be in effect immediately after being posted on this page.
Specifications
Sorry, currently do not have any video uploaded.
Sorry, currently do not have any file for download.
view more about
Torque Meter
